Saturday 11 August 2018

Red Army's White Tanks

Issues with reducing visibility of armoured vehicles arose as soon as these vehicles were first used. Like 100 years ago, opposing sides aim to locate enemy vehicles in motion, during stops, and during combat, determine their type and number, and also make the same as difficult as possible for the enemy. It's not easy to conceal a tank from the enemy, especially in winter. Areas covered in snow make dark objects (such as tanks in basic camouflage) very noticeable. How was the issue of camouflaging tanks in winter handled in the Red Army?


Types of winter paint schemes

Guides and manuals used in the USSR in 1941-1945 describe two types of winter paint for Soviet armoured and transport vehicles:
  • Monotone white
  • Deforming irregular spots
BT-5 tank. A portion of the vehicle is coloured in completely with white paint, and a portion is covered in white stripes on top of the base paint. The stripes are 1-3 cm wide and spaced 8-12 cm apart.

Monotone white paint reduces the visibility of a tank in winter and is the simplest type of winter camouflage. Deforming camouflage with spots and stripes not only makes the tank more difficult to see, but also makes it harder to hit, deforming its silhouette and making it harder to gauge distance. The effectiveness of both types of camouflage from the air is nearly identical. These factors combined make the deforming camouflage with spots preferable, even though it is harder to apply.

A T-50 tank. Note the different width of the stripes and the distance between them.

60-70% of the surface was coloured in white. The rest was left in camouflage green, which looked like dark spots on a white background. It turned out to be useful to cover these spots in white stripes, forming a grid. This was necessary to make the dark spots stand out less, since from a distance they appeared blurred and gray, like bushes. This made the camouflage more effective from short distances, such as in ambushes. This camouflage was also useful in settlements, as the white snow cover is broken up with highly contrasting dark buildings, objects, and shadows.

A T-40 tank. You can see that the paint was applied in several layers, and the degree of transparency varies. The headlights are fully painted over.

Lime, paint, plaster, glue

Methods of application deserve separate attention. There were several recipes, differing in difficulty and effectiveness.
  1. Lime diluted with water. Salt was added to make it hold better and a little laundry blue to make the colour brighter.
  2. Dry factory white paint. It was composed of two powders: a mix of casein and chalk (1 part) and slaked lime (2 parts). 1 part water was added and the mixture was thoroughly mixed over half an hour. 100 g of dry substance was used to cover one square meter.
  3. Paint with glue mixed in. 1 kg of painter's or wood glue was soaked in water, then diluted in a bucket of water, where 4-5 kg of chalk, plaster, kaolin clay, or slaked lime was added. This substance held onto surfaces very well.

A KV-1 tank. Smears and uneven paint application can be seen on the front. The grid was applied even to the headlight.

About a bucket of paint and 6-8 hours was spent to camouflage a tank. A car took half as much time and materials. It was suggested that the surface should be clean of dirt, oil, and snow before painting. The mixture should be kept warm during painting, and work should be done indoors with heat.

Adhesion of various substances to the tank varied, as well as resistance to precipitation and impacts. The first recipe was suggested for quick application using items available at hand, but it also had the shortest lifespan. Recipe #2 was more difficult and less accessible, as it was made at the factory, and recipe #3 took more time. However, the substance remained for longer due to the presence of glue in the mix.

A T-40 tank. The paint covers the entire surface of the vehicle, including the wheels and armour behind the tracks.

Concealment on the move and during stops

A tank reveals itself while moving by leaving marks with its tracks and throwing up dirt and snow. Movement during the winter was to be done at night time, and on roads instead of open fields. If one had to move through a field, it was suggested that the tanks go in single file, following each other's tracks, so it would be harder to count the number of tanks that passed.

One method of covering tracks is by using drags. A drag could be made from anything at hand (bushes or trees tied to the rear of the last tank in a column) or specially produced materials, such as 8-10 reels of barbed wire on a pole. These devices covered the tracks of passing vehicles and made it look like the road was not used.

To reduce visibility of vehicles, it was suggested that one turns off headlights or uses light-concealing attachments, creates decoy sounds away from where the tanks are really moving, etc.

A ZIS-6 in winter camouflage. Trucks were concealed with the same methods as tanks.

When tanks were stopped in settlements, sheds, ruins, and other large objects became useful for concealment. Covering vehicles with available materials (snow, straw, branches) was considered effective. When stopped in the forest in winter, evergreen trees were considered the most effective cover. Artificial lowering of the branches was used to conceal vehicles from above.

A tank under a tree where the branches were artificially lowered.

When it was necessary to stop tanks out in the open, they should be stopped within dark spots. These could be bomb craters, dirt thrown up by explosions, branches taken from forests, or artificially created spots (with branches, straw, or ground cleared from snow). The tank and its shadow stood out less when observed from the air.

If it was impossible to use natural dark spots, white netting or netting with white spots could be used. These nets could be seen from the air, but it was impossible to determine what was underneath, if anything at all.

Camouflage using a standard issue net that imitates tracks from a previous camp.

If necessary, a tank could be covered with a model of a local object (a shed, a haystack, ruins of a house). This technique was especially useful during ambushes. It also had its drawbacks, namely decreased fire safety and difficulty in leaving the vehicle. 

Ideally, a group of tanks could be concealed in one go. Cover was built in ravines, near vertical banks
or steep slopes. Large chunks of snow were cut out. These chunks were stacked in walls placed one tank width away from the slope. This hiding spot was covered with branches from above, then a layer of bushes, standard issue camouflage nets, or some other layer. After this, the "roof" was covered with snow. A hiding spot like this could house 5-10 vehicles. Special care had to be taken to remove the tracks leading into the "dead end". After that, it was nearly impossible to detect such an improvised garage from the air.

Measures to conceal tanks were taken at by tank battalion commanders (development of movement routes, overall control over carrying out of instructions) and platoon commanders (choosing places to stop, choosing how to approach them, directions regarding camouflage methods).

Most of the work to conceal a tank was done by its crew. In exceptional circumstances, this work could be carried out by sappers or special camouflage teams. As a rule, these were used to create group hiding spots and to paint tanks en masse.

The measures taken to conceal tanks in winter were simple and cheap methods to reduce the visibility of vehicles during combat and in between battles. Timely and proper use of these measures increased the combat effectiveness of units and reduced losses in battle.

5 comments:

  1. As a former tanker it quickly became apparent that any fancy paint job is a waste of time because most tanks quickly become covered with whatever type of material they are driving through. The best you can do is find a good place to hide and use local cover. But as soon as you start moving a person would need to be blind not to see a moving tank.

    ReplyDelete
  2. The T-50 with the 2/3 white and 1/3 green was probably a three-tone camouflage underneath the whitewash, with the white covering up everything except the green.

    ReplyDelete
    Replies
    1. This comment has been removed by the author.

      Delete
    2. If you were painting over three-tone camouflage, the directive was to paint white over green, a dense hatch over the yellow, and a less dense hatch over the brown.

      Delete
  3. really nice article love the camo for the russians in ww2! :D

    ReplyDelete