Wednesday 12 August 2020

76 mm HEAT Instructions

"October 28th, 1942
Instructions for firing 76 mm HEAT rounds from the 76 mm regimental gun model 1927
  1. The BP-353A 76 mm HEAT made from gun iron is introduced into the ammunition loadouts of 76 mm regimental guns model 1927 to fire at tanks.
  2. The BP-353A HEAT shell is an effective method of fighting any known enemy tank. The most effective distance to fire this shell at is up to 500 meters. Firing at up to 1000 meters is permitted.
  3. The HEAT shell penetrates the following amount of armour:
    Range
    At 90 degrees
    At 60 degrees
    100
    60
    50-60
    1000
    60
    50-60
  4. A brief firing table for HEAT shells should be inscribed on gun shields.
  5. The HEAT shell is equipped with the K-6 fuse. Keep in mind that the fuse goes off when it hits armour but may not go off if it hits terrain.
  6. The HEAT shell can be distinguished from other 76 mm rounds by the designation BP-353A on the hull, three round grooves on the ogive part, and the fuse (the K-6 fuse is several times smaller than the KTM-1 fuse).
  7. Use the following firing table when using the HEAT shell.
    Scale: ChGD (new sight) or "HE grenade K fuse 290 m/s (old sight).
    Angle of incidence +18 mils
    Range
    Setting
    Trajectory height
    Time in flight
    Impact velocity
    Descent angle
    Deviation
    Divisions
    Mils
    Vertical
    Horizontal
    100
    4
    0
    0.1
    0.3
    287
    0.22
    0.0
    0.0
    200
    7
    6
    0.6
    0.7
    284
    0.44
    0.1
    0.1
    300
    10
    11
    1.4
    1.0
    281
    1.06
    0.2
    0.2
    400
    14
    17
    2.5
    1.4
    278
    1.28
    0.3
    0.3
    500
    17
    23
    3.9
    1.7
    275
    1.51
    0.4
    0.4
    600
    20
    29
    5.6
    2.1
    272
    2.14
    0.5
    0.4
    700
    23
    36
    7.6
    2.5
    269
    2.37
    0.6
    0.5
    800
    26
    42
    10
    2.9
    267
    3.0
    0.7
    0.6
    900
    29
    48
    13
    3.2
    264
    3.24
    0.8
    0.6
    1000
    32
    55
    16
    3.6
    261
    3.49
    0.9
    0.7
    Note: in addition to gun iron BP-353A rounds you may also encounter steel BP-353 rounds. Those can be distinguished by the label BP-353 and K-6 fuse.
    Steel rounds use the same firing tables as gun iron rounds.
  8. Until special unclassified instructions are published, supply gun batteries with excerpts from these instructions with the muzzle velocity and penetration.
    The first batches of ammunition will include memos regarding firing HEAT shells.
  9. The following labels are applied to the ammunition crates:
    1. On the front: 76-27 HEAT x5
    2. On the lid: "fire as instructed in the memo inside the crate"
  10. The propellant casing is marked UBP-353A or UBP-353.
  11. Study the effect of these shells thoroughly and report to the GAU.
Attachment: an example of the memo included in the crate.

Authorized representative of the GAU Chief and Artillery Committee Chair, Major General Hohlov
Military Commissar of the GAU, Regimental Commissar Vasilyev
Acting Chief of the 1st Department of the Artillery Committeem Engineer-Colonel Slukhotskiy."

1 comment:

  1. Thanks for the firing table. I has a lower MV than I even had estimated. Good luck trying to hit a moving target with this shell.

    ReplyDelete